Aces High Bulletin Board
Welcome,
Guest
. Please
login
or
register
.
Did you miss your
activation email
?
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
Home
Help
Calendar
Login
Register
Hitech Creations Home Page
Aces High Bulletin Board
»
Help and Support Forums
»
Help and Training
»
Dot Command For Trim Settings?
« previous
next »
Print
Pages: [
1
]
Go Down
Author
Topic: Dot Command For Trim Settings? (Read 464 times)
katanaso
Gold Member
Posts: 2480
Dot Command For Trim Settings?
«
on:
August 23, 2010, 11:15:37 PM »
Is there a dot command to set trim to a specific place?
For example, if I want the elevator trim 3 clicks below neutral, is there a command that will do this? I would then assign it to a button on my throttle.
Thanks,
mir
Logged
mir
80th FS "Headhunters"
The most terrifying words in the English language are: "I'm from the government and I'm here to help."
Soulyss
Platinum Member
Posts: 6558
Re: Dot Command For Trim Settings?
«
Reply #1 on:
August 23, 2010, 11:25:11 PM »
Not specifically no, however there is the "trim set" button that I just learned about. Hold control inputs (roll, pitch, yaw) where you want them and hit "." that will trim the plane to maintain that position hands free. Quite useful flying home on one engine.
Logged
80th FS "Headhunters"
I blame mir.
Silat
Gold Member
Posts: 2536
Re: Dot Command For Trim Settings?
«
Reply #2 on:
August 23, 2010, 11:59:46 PM »
GoodSoul has a lot of experience flying with one engine..............
Logged
+Silat
"The first time someone shows you who they are, believe them." — Maya Angelou
"Conservatism offers no redress for the present, and makes no preparation for the future." B. Disraeli
"All that serves labor serves the nation. All that harms labor is treason."
katanaso
Gold Member
Posts: 2480
Re: Dot Command For Trim Settings?
«
Reply #3 on:
August 24, 2010, 02:44:39 PM »
Yeah, you mentioned that one the other night, Soulyss.
I was hoping for something that would go to an automatic trim setting that I like using when in the 38.
Right now, I have to manually trim down and zoom in a little bit to see where it is because the red line is hard for me to see.
I guess I can make a new wish in the Wishlist Forum.
Logged
mir
80th FS "Headhunters"
The most terrifying words in the English language are: "I'm from the government and I'm here to help."
FLS
AH Training Corps
Plutonium Member
Posts: 11618
Re: Dot Command For Trim Settings?
«
Reply #4 on:
August 24, 2010, 04:14:28 PM »
The Saitek 3-axis controller is nice for adding analog trim control. The AH auto trim overrides the analog trim and when the auto is off it goes to the pre-set analog positions. You you mark a scale for the 38 on it and you could see where you were setting it without looking at the cockpit indicator. You could also use it as a twin throttle and elevator trim control.
«
Last Edit: August 24, 2010, 04:49:19 PM by FLS
»
Logged
Aces High Help
Aces High Training
katanaso
Gold Member
Posts: 2480
Re: Dot Command For Trim Settings?
«
Reply #5 on:
August 24, 2010, 07:33:34 PM »
Thanks, FLS. That's pretty cool! Is it the 3-lever item that comes with the yoke?
Logged
mir
80th FS "Headhunters"
The most terrifying words in the English language are: "I'm from the government and I'm here to help."
FLS
AH Training Corps
Plutonium Member
Posts: 11618
Re: Dot Command For Trim Settings?
«
Reply #6 on:
August 25, 2010, 08:21:18 AM »
I believe it's the same one that comes with their yoke. It also has buttons at one end of each axis as well as the 3 rocker switches. This lets you use a throttle axis for example to toggle engine on/off or the RPM lever to toggle WEP.
Logged
Aces High Help
Aces High Training
Print
Pages: [
1
]
Go Up
« previous
next »
Hitech Creations Home Page
Aces High Bulletin Board
»
Help and Support Forums
»
Help and Training
»
Dot Command For Trim Settings?