Author Topic: New CH USB Gear and New Problems. (Read 341 times)

eskimo2 · « **on:** January 16, 2003, 11:07:36 PM »

I just got new USB CH PRO Throttle, Fightersick, and Throttle. I had been putting up with the same set-up in a very spikey analog/gameport version for years. I'm astonished to see solid lines on the graphs, especially after using a truckload of TM, Saiteck and CH analog stuff on 3 puters over the past 6 years. Never seen solid lines before.

However, I have problems,

First of all, I think the CH Control Manager program and its directions were either written by 7th graders or perhaps monkeys...

I can't believe that CH went from Speedkeys to this CH Control Manager GARBAGE. The first time I used Speedkeys, everything worked right away, I was programing it within 10 minutes, done in an hour or two. I don't even think I read the directions, it just made sense. This new CH Control Manager V1.31 does not make sense. Things are poorly defined and explained in the Help section, and it lacks pictures. It's kind of a "Who's on First" routine. Most importantly, things don't work like they should.

When I try to caliibrate the throttle in CH Control Manager, it thinks its a joystick and asks me to move it to the right. The JS and throttle seem to calibrate OK.

I read through this thread (< CH HOTAS USB Troubles > in Tech support). From it I was able to get the basic joystick, throttle, rudder and toe brakes working in AH. But not the buttons. Folks said they used the CH Control Manager to program the buttons. I programed just 3 buttons to test it out and when I went into AH. Well the buttons now work, but all of the axis contols have been lost, except for the throttle. Also, button #3 on the JS makes the mode light flip out every time I hit it. This button is a must because it is my straight up veiw.

I reassigned the > AH Control > to > Joystick > to > Joystick Control> in Aces High. It still only recognizes the throttle. So now what? Do I have to erase the joystick button commands now... somehow.

4 hours working on this, reading the Control Manager Help and related BB posts, writing this... Feel like Iv'e gotten nowhere!
Irritated, disapointed, and going to bed (its midnight).

Thanks for any replies.

(BTW, I'm running it all through a Powered Belkin 4 port USB hub)

eskimo

eskimo2 · « **Reply #1 on:** January 16, 2003, 11:24:42 PM »

OK, I just disabled mapping in the CH Control Manager. I now have all of my axis back, as well as a default POV hat, fire buttons, but button #3 does not look up and still switches modes on the lights...

I'm really going to bed now.

eskimo

funkedup · « **Reply #2 on:** January 17, 2003, 12:23:42 AM »

Uninstall everything, go to the CH Products website, get Control Manager 2.

DAVENRINO · « **Reply #3 on:** January 17, 2003, 02:37:52 PM »

ESKIMO,
If you only use the controls to play AH, you don't even need control manager. I don't even have it installed. Just set it up in AH setup as Airspro explained in "(< CH HOTAS USB Troubles > in Tech support). "

It took me all of 15 minutes to set up. You didn't say what OS but Airspro did it with 98 and I have XP Pro SP1.

Check this thread, too.
http://www.hitechcreations.com/forums/showthread.php?s=&threadid=74947

DJ229

eskimo2 · « **Reply #4 on:** January 18, 2003, 02:22:48 AM »

Thanks guys,

I downloaded Control Manager 2, and everything works like it shoud.

eskimo

Wotan · « **Reply #5 on:** January 18, 2003, 08:19:39 AM »

i dont use the ch manager either