Aces High Bulletin Board

Help and Support Forums => Technical Support => Topic started by: Booky on September 30, 2004, 12:44:27 AM

Title: Can't see Ground Vehicals
Post by: Booky on September 30, 2004, 12:44:27 AM

I have set my ground visual range to its max, 3 miles I believe, but I still can not see enemy vehicals when I am in an aircraft.  I can in no way attempt to dive bomb them because by the time I see them I am well below 1000ft AGL which leaves me no time to correct my target.

Is there any way to make it so the vehicals do not go transparent when I get above 1000ft agl?  I have plenty of system resources left as I am still running 75+fps.

I run WINXPSP2, Nvidia GF4 4200, SB Live, Barton 2500+, 1GB of PC2700.  I am useing a video driver in the early 50's range because the newer ones cause stability issues for me.

Thanks for any help.

Title: Can't see Ground Vehicals
Post by: fuzeman on September 30, 2004, 12:53:16 AM

My only advise would be to use the Shft F4, Ground Vis Range.
It may need to be key-mapped to use it.
http://www.hitechcreations.com/forums/showthread.php?s=&threadid=131292

Title: Can't see Ground Vehicals
Post by: Booky on September 30, 2004, 02:26:00 AM

Thank you for the fast response, I will try this when I get home.  So I assume that you are telling me to hit shift + F4 and it will cycle ground view distance in a different way than the slider in settings?  Also, what do you mean when you say that it may need to be mapped?  It has been over a year since Ive played AH activly and I forgot almost everything, im a noob again :-/

Title: Can't see Ground Vehicals
Post by: flyingaround on September 30, 2004, 02:13:11 PM

Yes you have to map the Ground View.  Go into your keyboard setup in AH, and in the VIEWS catagory (going from memory here) you will see a GROUND detail, map the to Shift F4 (or any key really, it's just that the OTHER detail views are shift F1-3).

Ground view extends your viewable distance to 4k (vs. the 3k max, and/or whatever you have setup for ground view in video pref's.) and you will be able to see those gv's now.  Unfort, it will also give you a hit to your FPS

Title: Can't see Ground Vehicals
Post by: Booky on September 30, 2004, 09:52:51 PM

Ok, I had a few moments to test this out this morning, unforunetly I wasn't able to be in an aircraft trying to bomb a GV.

When I hit Shift+F4 the horizon changed from its smooth view (Full view mode Shift+F1) to a Jagged mode labed Ground view.  It said ground view on text.

Is this what you are refering to?  I also checked the mapping and it was already mapped, I think.  It had Ground view  and then Shift+F4 listed.

I'll look again to see if I see a ground detail setting, other than the slider.  I don't have much time to check this stuff out untill Sunday.  Thanks for the help.

Title: Can't see Ground Vehicals
Post by: fuzeman on September 30, 2004, 11:10:18 PM

That's it. It will reduce the horizon but make the GVs more visable. As mentioned it does put a dent in the frame rate.

Title: Can't see Ground Vehicals
Post by: Elfie on October 01, 2004, 08:52:47 PM

Quote

Originally posted by fuze
That's it. It will reduce the horizon but make the GVs more visable. As mentioned it does put a dent in the frame rate.

I have tryed this, the *fr dent* is unacceptable. I go from 40's - 50's on my fr to the teens. Anyway to make it playable?

Athlon 2000
FX5700LE 128m vid
Audigy sound
512m ram
Win XP Pro
Diectx 9.0b

Title: Can't see Ground Vehicals
Post by: OOZ662 on October 01, 2004, 11:40:16 PM

Ram and vid card look good, dunno about prossy speed (cuz unless ya post it I have no clue. Not one of those guy who ya tell em a brand and they list off all the speeds..dam bots :rofl )

Title: Can't see Ground Vehicals
Post by: Booky on October 02, 2004, 03:23:59 AM

Thanks, I tested it out today for the one flight I had (attack) and it works.  My fps didn't drop too bad, only to about 45.  Now them pesky critters are once again going to see the iron powder in thier eyes.