Aces High Bulletin Board
General Forums => Hardware and Software => Topic started by: StokesAk on December 03, 2009, 08:37:14 PM
-
How can I preserve the life of my joystick, I have had problems with spiking in the past after about only 6 months.
Are there any ways that I could maximize the life on my joystick.
-
How can I preserve the life of my joystick, I have had problems with spiking in the past after about only 6 months.
Are there any ways that I could maximize the life on my joystick.
What brand are you getting?I know that has lots to do with it I have a mircrosoft sidewinder probably about 7 years old and it works great it don't have a spring though but its still a great stick. But no I don't have any tips on how to preserve it
-
What stick is it? No real way to 'preserve' it although some people have methods to fix problems with more expensive sticks (such as X52 and CH).
-
Unless you convert from potentiometers to Hall effect sensors you're going to get spiking eventually. Metal on metal will wear out, and you'll get spikes or dead zones. Keep in a relatively temperature stable, low dust environment and the should last 4 or 5 years. Unless the pots are cheap. If that's the case, check out DigiKey or another electronic parts supplier for something physically similar with the same ohm rating and replace them.
-
buy a CH one. Won't need another.
-
First let's hear what stick he has before making suggestions.
If he starts his sentence with "Its a Logictech -- " we can cut him off right there and say "get another one"
Otherwise, let's see what he's got to say :aok
-
i want to get my CH fanboi comment in quick though :D
but then again if everyone goes and gets CH gear it will be a level playing field and that wouldn't be good for my K/D. :rolleyes:
errrr yea get logitech they are well good an real cheap ya know. ;)
-
If it is Logitech.....
Logitech has a "Clear Calibration " utility on their website. Clears out fragmented calibrations, which causes stick spikes. I used to have a Logitech, and had spike problems till I used that. It's a program that apparently a lot of people did not know is out there. Hope this helps some people.
If you have a Saitek, sometimes spikes will occur, usually a pulll to left/right. If you twist (rudder) left, right , left. Then let center, it self calibrates.
<S> oz
-
Posting this reply (copied and pasted, no less) in every joystick thread there is won't solve the problem.
I tried the so-called utility, and it did nothing when I had a wingman stick. The problem is not anything software can fix. It's a hardware issue. The issue is that Logitech uses cheap hardware, and it dies quickly. Once a pot starts going it is done for, it will never get better, and no software will help.
-
If you don't use it and keep it in the box it should last forever. :D
-
How can I preserve the life of my joystick, I have had problems with spiking in the past after about only 6 months.
Are there any ways that I could maximize the life on my joystick.
Easy- quit masturbating so frequently! :neener: :bolt:
-
Convert to Hall sensors if you can or buy some spare potentiometers from the manufacturer
or a 3rd party vendor. Anticipating the same problem aftr my first pot went south in my CH F16
fighterstick I bought about 10 pots to replace any that went bad in the future. So far the supply
has outlasted my online game playing days.
TIP: Whatever you do do not use WD-40 to clean potentiometers out with. It is not a good,
long term solution. Use a can of TV-Tuner/Control Cleaner & Lubricant from Radio Shack for
example to blow junk and oxidation out and to lube the contacts inside.
-
Its the Cyborg X from Saitek
-
If you don't use it and keep it in the box it should last forever. :D
I have brand new logitech force feedback 3d pro in box, very good as a paper weight :frown: