Aces High Bulletin Board

General Forums => Hardware and Software => Topic started by: hlbly on January 28, 2010, 07:53:31 AM

Title: Anyone have a g940 profile they care to share for AH2 ?
Post by: hlbly on January 28, 2010, 07:53:31 AM: Looking for a place to start with profiling software . I started working on one and had a power outage :mad: after a few hours work on one . :furious . I am not sure I will use profiling software just would like a chance to try one and decide for myself .
Title: Re: Anyone have a g940 profile they care to share for AH2 ?
Post by: FLS on January 28, 2010, 09:09:10 AM: PM me your address and I'll send you one.
Title: Re: Anyone have a g940 profile they care to share for AH2 ?
Post by: Kirin on January 28, 2010, 10:58:34 AM: Got one too - quite simple but enough to work with. Includes buttons for TrackIR Center and Pause. Trim on rotaries.
Title: Re: Anyone have a g940 profile they care to share for AH2 ?
Post by: Skeksis on March 30, 2010, 02:45:32 AM: How did you get the rotaries working for trim?
Title: Re: Anyone have a g940 profile they care to share for AH2 ?
Post by: FLS on March 30, 2010, 07:40:09 AM: You just assign them in AH.
Title: Re: Anyone have a g940 profile they care to share for AH2 ?
Post by: Wagger on March 30, 2010, 08:30:15 AM: Yea how did you get the trim rotaries to work in AH. They don't seem to work for me.
Title: Re: Anyone have a g940 profile they care to share for AH2 ?
Post by: FLS on March 30, 2010, 08:45:42 AM: I just assigned them the same way you assign the stick, throttle and rudder pedals. You don't do anything in the Profiler, just assign them in the AH controller setup.
Title: Re: Anyone have a g940 profile they care to share for AH2 ?
Post by: Skeksis on June 13, 2010, 05:23:42 PM: Quote from: FLS on March 30, 2010, 08:45:42 AM
I just assigned them the same way you assign the stick, throttle and rudder pedals. You don't do anything in the Profiler, just assign them in the AH controller setup.

I wonder what I am doing wrong then. I tried assigning them and did not have much success with the attempt. What I ended up with was one of them controlling elevator trim and the other controlling aileron trim but only in one direction so right now the trims are assigned to a hat. Any suggestions how I got this messed up?

Thanks!
Title: Re: Anyone have a g940 profile they care to share for AH2 ?
Post by: hlbly on June 14, 2010, 08:23:35 AM: Assign all button functions in profiler . Assign all analogue functions in Aces high .
Title: Re: Anyone have a g940 profile they care to share for AH2 ?
Post by: FLS on June 14, 2010, 12:22:02 PM: Quote from: Skeksis on June 13, 2010, 05:23:42 PM
I wonder what I am doing wrong then. I tried assigning them and did not have much success with the attempt. What I ended up with was one of them controlling elevator trim and the other controlling aileron trim but only in one direction so right now the trims are assigned to a hat. Any suggestions how I got this messed up?

Thanks!

Calibrate the rotaries in windows, be sure they are centered for the center calibration, then calibrate them in AH. After you assign them in AH select the advanced tab and check the functioning.
Title: Re: Anyone have a g940 profile they care to share for AH2 ?
Post by: morfiend on June 14, 2010, 12:58:38 PM: I could be mistaken but if they are analog controls and you have combat trim set on by default you must first overide combat trim. You could toggle it off or turn it off in preferences,myself I use CT so I toggle it on or off and it must be off for my analog trim controls to work.

Hope this helps!

:salute