Aces High Bulletin Board

General Forums => Hardware and Software => Topic started by: Hakster on May 04, 2001, 02:16:00 PM

Title: Problem with Geforce 2 MX
Post by: Hakster on May 04, 2001, 02:16:00 PM
Hi
I have just replaced my Voodoo 3 3000 AGP with a Guillemot Hercules Geforce 2 MX and now I canīt play AH.
A few seconds(or sometimes even a minute) after getting in the cockpit my computer hangs completely. Nothing to do but to hit the reset button.
I have tried the drivers that came with the card and with Detonator 3.

Please heeeeelp

Hakster
Title: Problem with Geforce 2 MX
Post by: Spatula on May 05, 2001, 06:33:00 PM
I had the same problems.

What fixed it for me was to disconnect some harddrives from the power supply. GForce 2s take quite a bit of power to run and will just lock the computer up seemingly random or worse if they dont get enough juice.

So, either get a gruntier power supply 300Watts minimum OR disconnect some peripherals like hard drives as they use alot of power.

Fail that. List your complete system specs so people know what you have etc. Also check out:  http://www.geforcefaq.com/ (http://www.geforcefaq.com/)  

or check out my thread from a month or so back. http://bbs.hitechcreations.com/smf/Smileys/default/Forum6/HTML/002215.html (http://bbs.hitechcreations.com/smf/Smileys/default/Forum6/HTML/002215.html)

Hope something helps
Title: Problem with Geforce 2 MX
Post by: Hakster on May 06, 2001, 09:45:00 AM
Thanks Spatula.
Iīve heard that the GF cards take a lot of juice so perhaps I should invest in a 300w powersupply. Iīll read the links you provided first.

Hakster
Title: Problem with Geforce 2 MX
Post by: whels1 on May 06, 2001, 10:48:00 AM
 
Quote
Originally posted by Hakster:
Thanks Spatula.
Iīve heard that the GF cards take a lot of juice so perhaps I should invest in a 300w powersupply. Iīll read the links you provided first.

Hakster


also older motherboards before jan 2000 has/had problems being able to supply enough I/O volts to the new v5/gfs cards. see if u can up your I/O volts on your MB.  Skuzzy also recommends antec power supplies.

whels
Title: Problem with Geforce 2 MX
Post by: Hakster on May 07, 2001, 03:57:00 PM
I have checked in bios but I canīt find anywhere where I can change i/o voltage.
Current i/o voltage is 3.2v(if I looked at the right numbers??).
The motherboard is 2 or 3 years old.
It looks like I will be taking the GF2 card back to the shop and continue to use my Voodoo3.

Hakster
Title: Problem with Geforce 2 MX
Post by: whels1 on May 07, 2001, 06:40:00 PM
 
Quote
Originally posted by Hakster:
I have checked in bios but I canīt find anywhere where I can change i/o voltage.
Current i/o voltage is 3.2v(if I looked at the right numbers??).
The motherboard is 2 or 3 years old.
It looks like I will be taking the GF2 card back to the shop and continue to use my Voodoo3.

Hakster

id not go back to the V3, but exchange it if u can for a GF2 MX.  not as power hungery as a full bore gf2 but far better then a v3.

Whels