Aces High Bulletin Board
General Forums => Hardware and Software => Topic started by: Serenity on December 17, 2014, 05:11:05 PM
-
So, system specs first:
I'm running a 600W PSU (I don't know the manufacturer)
Saitek X55 Rhino
Saitek ProRudders
My stick is spiking. It's spiking OUT OF CONTROL. Like, EVERY single switch and button thinks it's being activated CONSTANTLY while flying. The stick axes (axises?) are fine, no spiking there, but the rudders tend to jump. It's impossible to play with the level of spiking. I had heard that adding a powered USB hub would help, so I went out and got one today. No improvement. I had been told that using the Saitek profile software sometimes caused this issue, so I deleted the software, and in DCS the problem seemed to be fixed, but in AH it got drastically worse (And I didn't think that was possible). The sticks are less than a month old. What could I possibly do to fix this?!
-
Does the stick spike without the pedals connected? Can you calibrate the controllers in windows?
-
As a long time user of multiple X-52s, I experienced spiking at random times. The solutions ranged from unplugging the joystick, to unplugging both, to using a different slot on the usb hub. After a computer changeover, I neglected to install the software or even a driver for the X-52. Now the very same stick that would go haywire on a weekly basis has been solid for months (hope I didn't just jinx myself). Also, the X-52 pro I had was spiking on the new computer as well, so maybe you could try removing the driver.
-
Does the stick spike without the pedals connected? Can you calibrate the controllers in windows?
Yes, it still spikes without the rudders.
I can calibrate with the Saitek program. I don't know how one would calibrate in windows, especially calibrating buttons.
As a long time user of multiple X-52s, I experienced spiking at random times. The solutions ranged from unplugging the joystick, to unplugging both, to using a different slot on the usb hub. After a computer changeover, I neglected to install the software or even a driver for the X-52. Now the very same stick that would go haywire on a weekly basis has been solid for months (hope I didn't just jinx myself). Also, the X-52 pro I had was spiking on the new computer as well, so maybe you could try removing the driver.
I've tried all of those as well. I guess I uninstall the drivers next... How do you uninstall a driver?
-
Hey Serenity.
Google JoyTester2 and download it.
Insure that you don't have any other USB controllers attached to your computer (mouse is okay) if you have a game pad or somesuch...pull it. Pull the pedals.
JoyTester2 will show you exactly what is going on with the Rhinos. If it is spiking, call SaitekUSA and tell them you're spiking in JoyTester2. They will probably send you a new set of sticks after walking you through their diagnostic...which is an uninstall - reinstall - test of the drivers.
The sticks have a two-year warranty from Saitek. If you bought them from Amazon, you can check your order history, and use the Amazon software to set up a return (broken), then just pack them up and return them. You will have your new Rhino probably after Christmas. I have a good set (after one return) and I still think they are worth the teething problems they've had.
You can't fix the sticks if it is hardware causing the spikes.
Question. Did I understand that you haven't been able to calibrate the Rhino in Windows?
:salute
-
Hey Serenity.
Google JoyTester2 and download it.
Insure that you don't have any other USB controllers attached to your computer (mouse is okay) if you have a game pad or somesuch...pull it. Pull the pedals.
JoyTester2 will show you exactly what is going on with the Rhinos. If it is spiking, call SaitekUSA and tell them you're spiking in JoyTester2. They will probably send you a new set of sticks after walking you through their diagnostic...which is an uninstall - reinstall - test of the drivers.
The sticks have a two-year warranty from Saitek. If you bought them from Amazon, you can check your order history, and use the Amazon software to set up a return (broken), then just pack them up and return them. You will have your new Rhino probably after Christmas. I have a good set (after one return) and I still think they are worth the teething problems they've had.
You can't fix the sticks if it is hardware causing the spikes.
Question. Did I understand that you haven't been able to calibrate the Rhino in Windows?
:salute
I haven't tried to calibrate them in windows. I don't actually know how.
-
Hey Serenity.
Google JoyTester2 and download it.
Insure that you don't have any other USB controllers attached to your computer (mouse is okay) if you have a game pad or somesuch...pull it. Pull the pedals.
JoyTester2 will show you exactly what is going on with the Rhinos. If it is spiking, call SaitekUSA and tell them you're spiking in JoyTester2. They will probably send you a new set of sticks after walking you through their diagnostic...which is an uninstall - reinstall - test of the drivers.
The sticks have a two-year warranty from Saitek. If you bought them from Amazon, you can check your order history, and use the Amazon software to set up a return (broken), then just pack them up and return them. You will have your new Rhino probably after Christmas. I have a good set (after one return) and I still think they are worth the teething problems they've had.
You can't fix the sticks if it is hardware causing the spikes.
Question. Did I understand that you haven't been able to calibrate the Rhino in Windows?
:salute
I downloaded joytester2 and cannot seem to figure it out, nor is there a real website to read up on it online, only a bunch of forum threads of people recommending it.
-
Spiking refers to spurious axis commands. Your description of active buttons sounds like a short circuit, bad ground, or a wiring problem.
Look at Devices and Printers in control panel. You should see your joystick. Right click the icon and select game controller settings then properties. This will show you if Windows sees the buttons as activating on their own.
-
Spiking refers to spurious axis commands. Your description of active buttons sounds like a short circuit, bad ground, or a wiring problem.
Look at Devices and Printers in control panel. You should see your joystick. Right click the icon and select game controller settings then properties. This will show you if Windows sees the buttons as activating on their own.
Just pulled it up, aaaaannnnddd magically the problem no longer exists, so I cannot diagnose it...
-
It will return :old:
Powered USB :old:
-
It will return :old:
Powered USB :old:
This helped with my Saitek
-
So. I had the same problem with my first Rhino. Spikes and crazy buttons. The problem was the windows calibration. I'm sorry JoyTester2 confused you. It's not friendly, really. When I started over I did the following -
1. Installed a powered USB Hub
2. Deleted the Saitek software and drivers
3. Removed all controllers other than the mouse
4. Shut down the computer and restarted with the Rhino plugged in
5. Went to Devices and Printers in Windows 7
6. Did a complete calibration of the stick and throttle including the all the rotary knobs
7. DID NOT HIT THE "APPLY" button at the end. Fired up Aces High, calibrated normally, and everything worked.
8. Then I loaded the Saitek programming software
9. Created a program for Aces High
10. Re-checked calibration in Windows 7
11. Began enjoying them and consistent enjoyment ever since.
I didn't write this process down...but I did report it back to Saitek who didn't believe me. I already had the return in progress when I did this, so I let them give me a new set of sticks (I had one stick button that was sticky).
Honestly I couldn't remember what I did when I responded to you last night.
I hope you have clear sailing from here.
:salute
-
It will return :old:
Powered USB :old:
Already done that, to no avail...
So. I had the same problem with my first Rhino. Spikes and crazy buttons. The problem was the windows calibration. I'm sorry JoyTester2 confused you. It's not friendly, really. When I started over I did the following -
1. Installed a powered USB Hub
2. Deleted the Saitek software and drivers
3. Removed all controllers other than the mouse
4. Shut down the computer and restarted with the Rhino plugged in
5. Went to Devices and Printers in Windows 7
6. Did a complete calibration of the stick and throttle including the all the rotary knobs
7. DID NOT HIT THE "APPLY" button at the end. Fired up Aces High, calibrated normally, and everything worked.
8. Then I loaded the Saitek programming software
9. Created a program for Aces High
10. Re-checked calibration in Windows 7
11. Began enjoying them and consistent enjoyment ever since.
I didn't write this process down...but I did report it back to Saitek who didn't believe me. I already had the return in progress when I did this, so I let them give me a new set of sticks (I had one stick button that was sticky).
Honestly I couldn't remember what I did when I responded to you last night.
I hope you have clear sailing from here.
:salute
Fantastic, thank you! If it starts ghosting again, I'll try this!
Edit: Problem is back, just tried this, we'll see how it works!
-
No improvement.
-
So I spent several hours talking to Saitek's customer service, and after trying everything, we determined that at the very least, the combination of Windows 8.1 and USB 3.0 ports on my computer are to blame. Windows 8 just sucks, and causes these problems. There is no fix at this time, other than to go buy Windows 7.
-
Shakes head, with empathy.
I sent my son off to Texas Tech in the fall with a touch screen laptop with Win 8.1 loaded. We're almost back on speaking terms. He hates it.
I'll sit on Win 7 64-bit for as long as I can.
Is MadKatz/Saitek going to refund your money?
:salute
-
Shakes head, with empathy.
I sent my son off to Texas Tech in the fall with a touch screen laptop with Win 8.1 loaded. We're almost back on speaking terms. He hates it.
I'll sit on Win 7 64-bit for as long as I can.
Is MadKatz/Saitek going to refund your money?
:salute
I'll have to call them back tomorrow. They made a couple more recommendations, then had to hang up as they were closing for the day, but I doubt I would get anything. The hardware is fine, they just don't have software that works with Windows 8.
I REALLY don't want to have to go install a new OS, but I don't want a $200 paperweight either. Anyone have any recommendations on how to install 7 with the least background crap possible?
-
Anyone have any recommendations on how to install 7 with the least background crap possible?
Use a generic installation media. That will give you the plain vanilla Windows unlike the bloated systems of any brand. I just installed one and it had 39 processes running. On my own rig I have about 30. www.blackviper.com (http://www.blackviper.com) is a good starting point in reducing background processes, but you'll also have to look at how you install additional stuff like Flash Player, PDF reader, printer, whatever - even your motherboard driver cd is probably bloated with unnecessary stuff! Drivers are necessary, everything else is mostly just shiny junk. When installing anything do a custom install, carefully thinking about every checked option and unchecking those that you really don't need. After installing anything look at its settings/options/preferences and set them never to automatically to look for updates. Also set them not to start at Windows startup.
-
Automatic update from microsoft other day screwed my sound card up
should read update properly Creative update from microsoft :cry
-
Thanks for the help gents!
-
Automatic update from microsoft other day screwed my sound card up
should read update properly Creative update from microsoft :cry
Word of advice: disable the driver update from your Windows update settings. http://support.microsoft.com/kb/2500967