« previous next »
Pages: [1]   Go Down

Author Topic: CH FighterStick Problem  (Read 265 times)

Offline Fencer51

  • Aces High CM Staff (Retired)
  • Platinum Member
  • ******
  • Posts: 4677
CH FighterStick Problem
« on: May 24, 2007, 05:42:25 AM »
I have a CH FighterStick (USB) that I bought last fall.  Some times it seems to be loosing the "pull back climb" input.  I can put a full deflection on it and either it slightly pulls of or nothing, then it will just jump to that position.  It seems to go away if I recalibrate in AH.

Any suggestions as to what might be wrong?
Logged
Fencer
The names of the irrelevant have been changed to protect their irrelevance.
The names of the innocent and the guilty have not been changed.
As for the innocent, everyone needs to know they are innocent –
As for the guilty… they can suck it.

Offline NOT

  • Nickel Member
  • ***
  • Posts: 780
CH FighterStick Problem
« Reply #1 on: May 24, 2007, 06:41:52 AM »
mine will do that occasionally, usually because i haven't calibrated in a while. i just recalibrate and go.



NOT
Logged



AKNOT

Offline Easyscor

  • Plutonium Member
  • *******
  • Posts: 10888
CH FighterStick Problem
« Reply #2 on: May 24, 2007, 08:43:18 AM »
Citabria had even worse problems until Michael from CH Products suggested he try a powered USB hub.
Logged
Easy in-game again.
Since Tour 19 - 2001

Offline doc1kelley

  • Silver Member
  • ****
  • Posts: 1508
Re: CH FighterStick Problem
« Reply #3 on: May 24, 2007, 09:15:53 AM »
Quote
Originally posted by Fencer51
I have a CH FighterStick (USB) that I bought last fall.  Some times it seems to be loosing the "pull back climb" input.  I can put a full deflection on it and either it slightly pulls of or nothing, then it will just jump to that position.  It seems to go away if I recalibrate in AH.

Any suggestions as to what might be wrong?


What they say... What they say... The powered USB hub is the way to go with CH USB equipment!  I also have to calibrate my Fighterstick every time I enter AH.  I do NOT use the CH control manager at all and all my stuff is mapped via AH's internal mapping.  I also use the "Belkin" powered USB port but there are others out there.

All the Best...
Jay
awDoc1
Logged
awDoc1
The Flying Circus Rocks! We're clowns of a different color!

Beer! helping ugly folks get laid!

Offline NOT

  • Nickel Member
  • ***
  • Posts: 780
CH FighterStick Problem
« Reply #4 on: May 24, 2007, 09:33:43 AM »
after reading the post on the usb hub, im gettin me one. :aok






NOT
Logged



AKNOT

Offline Fencer51

  • Aces High CM Staff (Retired)
  • Platinum Member
  • ******
  • Posts: 4677
CH FighterStick Problem
« Reply #5 on: May 24, 2007, 01:59:26 PM »
Ah but it just started doing it after 5 months of use...
Logged
Fencer
The names of the irrelevant have been changed to protect their irrelevance.
The names of the innocent and the guilty have not been changed.
As for the innocent, everyone needs to know they are innocent –
As for the guilty… they can suck it.

Offline Puck

  • Gold Member
  • *****
  • Posts: 2980
CH FighterStick Problem
« Reply #6 on: May 24, 2007, 02:15:52 PM »
Could also be dirty pots.  That sounds SO...nevermind.

The symptom is consistent with noisy output.  If you sit and watch the output numbers in the configuration menu do they bounce around?
Logged
//c coad  c coad run  run coad run
main (){char _[]={"S~||(iuv{nkx%K9Y$hzhhd\x0c"},__
,___=1;for(__=___>>___;__<((___<<___<<___<<___<<___
)+(___<<___<<___<<___)-___);__+=___)putchar((_[__
])+(__/((___<<___)+___))-((___&

Offline Auger

  • Nickel Member
  • ***
  • Posts: 492
      • AKs Home Page
CH FighterStick Problem
« Reply #7 on: May 25, 2007, 05:18:00 PM »
It could be a dirty or failing pot.  Run the calibration routine and see if it calibrates OK.  If not, it's probably time to RMA it to CH.

You also may want to check your AH settings and make sure your scaling, damping and deadband didn't get all out of whack.
Logged
Pages: [1]   Go Up
« previous next »