Author Topic: No AH2 vox  (Read 276 times)

Offline mtnman

  • Gold Member
  • *****
  • Posts: 2438
No AH2 vox
« on: June 07, 2004, 09:45:04 AM »
I have had no vox in AH2. Not able to transmit on channel, or range, and not able to recieve from either. I've uninstalled AH2 and done the full reinstall. I've updated my drivers, and my DirectX9, with no luck. All my microphone settings in Windows, and in AH2 seem to be in order. Vox works fine in AH1, and settings are the same. All other sounds in both games are normal. I'm not sure if this is a bug, or a driver/settings issue. Others have been complaining about this same problem, but only a few that I know of. Beyond email and AH, I'm basically computer illiterate, so I don't have any idea what to do next. Any help/info would be appreciated...If more info is needed, let me know - Mtnman


AMD Athlon XP 2400+
WD800JB 80 GB HD
512 MB DDR RAM
FX5600XT 256 DDR Video Card
Omega Drivers
DirectX 9.0b
Win XP
MtnMan

"Those who hammer their guns into plows will plow for those who do not". Thomas Jefferson

Offline Frodo

  • Platinum Member
  • ******
  • Posts: 7410
No AH2 vox
« Reply #1 on: June 07, 2004, 03:25:23 PM »
http://216.91.192.19/forums/showthread.php?s=&postid=1250686#post1250686

Mtnman try looking through this thread in the link above.Might give you some things to try. Good luck.

Frodo


JG11 

TEAMWORK IS ESSENTIAL....IT GIVES THE ENEMY SOMEONE ELSE TO SHOOT AT.

Offline mtnman

  • Gold Member
  • *****
  • Posts: 2438
No AH2 vox
« Reply #2 on: June 07, 2004, 04:45:29 PM »
Thanks for link to other post, but...I don't think the chips I have are VIA. My sound is on my MB, not an additional card. My sound info says.  
ON Board AC'97 Sound Codec
-Chip:ALC650
-Compliant with AC'97 specification
-AC'97 2.2 Interface
-Supports 6 channels.
Would the Hyperian drivers mentioned apply here? I know very little about computers, and am hesitant to start downloading without knowing what is going on.
My MB chipsets are-
North : nVIDEA nFORCE2 400
South: nVIDEA nFORCE2 MCP/MCP-T
Do I need to do updates for those too? I do the windows updates regarding drivers, etc, and am current there, but again, don't know what is best or where to look.
Tried reducing hardware acceleration, no change, so put back to highest setting.
Checked firewall setting in network connections, and it is not/was not enabled. Also have AV turned off when restart for AH.
DxDiag? Don't know how, or how to get it to post here. I lose TCP/Switch to UDP every time I play, within 5-10 minutes and always have, with no noticable effect, even in AH1. Could that be related? I'm on dial-up, live in the sticks, with no access to cable, not able to pay for DSL. My connect is ussually 48.6- 50.2, with pings of 175-185. Not sure if that matters. Really miss my vox...Mtnman
MtnMan

"Those who hammer their guns into plows will plow for those who do not". Thomas Jefferson

Offline JB73

  • Plutonium Member
  • *******
  • Posts: 8780
No AH2 vox
« Reply #3 on: June 07, 2004, 06:52:46 PM »
do a BBS search for AC97...
skuzzy mentioned something about it quite a while back.

you might want to look into a $40 SB PCI card and disabling the onboard.
I don't know what to put here yet.