X52 loses calibration often

[The Fugitive]

Well...my system is a completely stock "out of the box" 7 year old Dell 

which powered hub are you using?

[Banshee7]

CyberPower...not sure if its anything else other than that

[kilz]

which powered hub are you using?

you use CH i have a question for you. i just got my CH set up for Xmas. however my throttle looses calibration everytime i log on. i have to recalibrate everytime. any ideas on what might be wrong or something i might have done wrong?

[Elfie]

The best fix for all these problems with Saitex gear is to simply throw that crap in the trash and buy all new CH gear. It's what I did and I haven't regretted it for a second. 

[The Fugitive]

CyberPower...not sure if its anything else other than that

I did a quick search and of the three I found one one of the has a plug to plug it into the wall for power. The other two have jacks that you can get a power cable for, or use a set of batteries. Is your hub plugged into the wall?

you use CH i have a question for you. i just got my CH set up for Xmas. however my throttle looses calibration everytime i log on. i have to recalibrate everytime. any ideas on what might be wrong or something i might have done wrong?

Kilz does it loose calibration in windows too? I know when I first set mine up with a Hub (you must use a powered hub for the CH gear to plug in to) I had to basically go through the "install" process a couple of times.... you know the "windows has found a new USB device" crap. After that I havn't calibrated my stuff in months.

[falcon23]

I also have cyberpower..Causes my x52 to bluescreen...


                                             Falcon23

[kilz]

I did a quick search and of the three I found one one of the has a plug to plug it into the wall for power. The other two have jacks that you can get a power cable for, or use a set of batteries. Is your hub plugged into the wall?

Kilz does it loose calibration in windows too? I know when I first set mine up with a Hub (you must use a powered hub for the CH gear to plug in to) I had to basically go through the "install" process a couple of times.... you know the "windows has found a new USB device" crap. After that I havn't calibrated my stuff in months.

just like today i logged in and had no throttle then i got it to work but would not go full throttle. do i need to just uninstall it and reinstall it?

[Eagler]

X52 hotas with ch pro peds - all into powered hubs - using AH programming inside the game - no problems here
first thing I do in AH is calibrate - all the axis including the rotors which are setup for trims

[The Fugitive]

just like today i logged in and had no throttle then i got it to work but would not go full throttle. do i need to just uninstall it and reinstall it?

First thing I would do is ALT TAB out of the game when I find it not working and check the game controllers to see if first windows sees it, and how it works there.

I think a reinstall may help. Unplug the throttle, reboot the computer, then plug the throttle back in. Let windows do it think again.

[Banshee7]

I did a quick search and of the three I found one one of the has a plug to plug it into the wall for power. The other two have jacks that you can get a power cable for, or use a set of batteries. Is your hub plugged into the wall?

Yes I have the one that plugs into the wall

[kilz]

First thing I would do is ALT TAB out of the game when I find it not working and check the game controllers to see if first windows sees it, and how it works there.

I think a reinstall may help. Unplug the throttle, reboot the computer, then plug the throttle back in. Let windows do it think again.

found the problem

1st i needed to take feet off of pedal brakes that i set up on pedals DUH

2nd i had the throttle set with invert clicked, so throttle full up was actually throttle down DUH again thanks for the help