« previous next »
Pages: [1] 2   Go Down

Author Topic: Which is best for a stable CH Setup....  (Read 2341 times)

Offline Changeup

  • Persona Non Grata
  • Platinum Member
  • ******
  • Posts: 5688
      • Das Muppets
Which is best for a stable CH Setup....
« on: December 21, 2012, 12:07:37 PM »
Powered USB hub or adding a USB 3.0 card with 4 ports on the MB?  
« Last Edit: December 21, 2012, 12:11:34 PM by Changeup »
Logged
"Such is the nature of war.  By protecting others, you save yourself."

"Those who are skilled in combat do not become angered.  Those who are skilled at winning do not become afraid.  Thus, the wise win before the fight, while the ignorant fight to win." - Morihei Ueshiba

Offline ebfd11

  • Platinum Member
  • ******
  • Posts: 4151
      • [b]POTW[/b]
Re: Which is best for a stable CH Setup....
« Reply #1 on: December 21, 2012, 02:04:17 PM »
I would go with BOTH ..
Logged
PIGS ON THE WING 3RD WING

InGame id: LawnDart
RIP Skullman Potzie and BentNail

Offline Changeup

  • Persona Non Grata
  • Platinum Member
  • ******
  • Posts: 5688
      • Das Muppets
Re: Which is best for a stable CH Setup....
« Reply #2 on: December 21, 2012, 02:06:31 PM »
Quote from: ebfd11 on December 21, 2012, 02:04:17 PM
I would go with BOTH ..

The powered hub is giving my stick and pedals spiking....
Logged
"Such is the nature of war.  By protecting others, you save yourself."

"Those who are skilled in combat do not become angered.  Those who are skilled at winning do not become afraid.  Thus, the wise win before the fight, while the ignorant fight to win." - Morihei Ueshiba

Offline TequilaChaser

  • AH Training Corps - Retired
  • Plutonium Member
  • *******
  • Posts: 10173
      • The Damned - founded by Ptero in 1988
Re: Which is best for a stable CH Setup....
« Reply #3 on: December 21, 2012, 02:32:17 PM »
Heya ChangeUp,

I have used CH gear since '95 and ever since I went USB type, I have never had to use an external USB powered hub or otherwise...

I have posted on here many years ago regarding not all MotherBoards Manufacturers are the same when it comes to the component quality and how they delegate the power draw, etc... this is one reason I have always been partial to using higher end ASUS MBs.....  I never have experienced the power/spiking issues that
alot of others constantly post about....

then again, most will have 6 to 10 USB pheripals plugged in and splitted off of etc of just 2 or 3 root hubs that Windows recognizes ( hope I posted that correctly )
so it results in not having enough power for all the extra USB items they are using.... like printers, lan connection, etc...

I do not see where using a USB 3.0 port will be of benefit any more than using a 2.0 USB port .... both still have the same 5 volt draw if I am not mistaken

powered USB hubs are a 50/50 ordeal....

wish you the best of luck in finding a cure

TC  ( yes I know I didnt use spellcheck )
Logged
"When one considers just what they should say to a new pilot who is logging in Aces High, the mind becomes confused in the complex maze of info it is necessary for the new player to know. All of it is important; most of it vital; and all of it just too much for one brain to absorb in 1-2 lessons" TC

Offline Changeup

  • Persona Non Grata
  • Platinum Member
  • ******
  • Posts: 5688
      • Das Muppets
Re: Which is best for a stable CH Setup....
« Reply #4 on: December 21, 2012, 02:40:15 PM »
Quote from: TequilaChaser on December 21, 2012, 02:32:17 PM
Heya ChangeUp,

I have used CH gear since '95 and ever since I went USB type, I have never had to use an external USB powered hub or otherwise...

I have posted on here many years ago regarding not all MotherBoards Manufacturers are the same when it comes to the component quality and how they delegate the power draw, etc... this is one reason I have always been partial to using higher end ASUS MBs.....  I never have experienced the power/spiking issues that
alot of others constantly post about....

then again, most will have 6 to 10 USB pheripals plugged in and splitted off of etc of just 2 or 3 root hubs that Windows recognizes ( hope I posted that correctly )
so it results in not having enough power for all the extra USB items they are using.... like printers, lan connection, etc...

I do not see where using a USB 3.0 port will be of benefit any more than using a 2.0 USB port .... both still have the same 5 volt draw if I am not mistaken

powered USB hubs are a 50/50 ordeal....

wish you the best of luck in finding a cure

TC  ( yes I know I didnt use spellcheck )

TC,

I've got a Sabertooth X58.  The 3.0 is just what I happened to pick up not for speed.  So which would you prefer?
Logged
"Such is the nature of war.  By protecting others, you save yourself."

"Those who are skilled in combat do not become angered.  Those who are skilled at winning do not become afraid.  Thus, the wise win before the fight, while the ignorant fight to win." - Morihei Ueshiba

Offline TequilaChaser

  • AH Training Corps - Retired
  • Plutonium Member
  • *******
  • Posts: 10173
      • The Damned - founded by Ptero in 1988
Re: Which is best for a stable CH Setup....
« Reply #5 on: December 21, 2012, 03:13:58 PM »
Hey Changeup, They both should work the same regarding your ch gear... I understand your reasoning
for wanting the 3.0 for increased data transfer speed...

That x58 board should provide you ample power for your ch setup, depending
on what other USB powered products you might be using

Hope this helps, Bro!

TC
Logged
"When one considers just what they should say to a new pilot who is logging in Aces High, the mind becomes confused in the complex maze of info it is necessary for the new player to know. All of it is important; most of it vital; and all of it just too much for one brain to absorb in 1-2 lessons" TC

Offline Changeup

  • Persona Non Grata
  • Platinum Member
  • ******
  • Posts: 5688
      • Das Muppets
Re: Which is best for a stable CH Setup....
« Reply #6 on: December 21, 2012, 05:35:30 PM »
Quote from: TequilaChaser on December 21, 2012, 03:13:58 PM
Hey Changeup, They both should work the same regarding your ch gear... I understand your reasoning
for wanting the 3.0 for increased data transfer speed...

That x58 board should provide you ample power for your ch setup, depending
on what other USB powered products you might be using

Hope this helps, Bro!

TC

The stick and the rudder pedals are the components that are "flickering" in the calibration area.  The throttle is fine.  I'm going to isolate each one by plugging them into the computer directly.  I suppose it could be the CH stuff.  I'll go ahead and install the 4 X 3.0....just cuz I need a computer-fixing fix.
Logged
"Such is the nature of war.  By protecting others, you save yourself."

"Those who are skilled in combat do not become angered.  Those who are skilled at winning do not become afraid.  Thus, the wise win before the fight, while the ignorant fight to win." - Morihei Ueshiba

Offline edog1977

  • Copper Member
  • **
  • Posts: 268
Re: Which is best for a stable CH Setup....
« Reply #7 on: December 21, 2012, 07:06:33 PM »
Do you have the CH software installed? When I switched to a CH stick and pedals I had a lot of spiking until I installed the CH software. Once I calibrated the pedals and stick in the CH manager and then in the game the problem went away.
Logged

Offline Changeup

  • Persona Non Grata
  • Platinum Member
  • ******
  • Posts: 5688
      • Das Muppets
Re: Which is best for a stable CH Setup....
« Reply #8 on: December 21, 2012, 07:07:44 PM »
Quote from: edog1977 on December 21, 2012, 07:06:33 PM
Do you have the CH software installed? When I switched to a CH stick and pedals I had a lot of spiking until I installed the CH software. Once I calibrated the pedals and stick in the CH manager and then in the game the problem went away.

I had it installed but I removed it.  I'm right in the middle of testing everything now.
Logged
"Such is the nature of war.  By protecting others, you save yourself."

"Those who are skilled in combat do not become angered.  Those who are skilled at winning do not become afraid.  Thus, the wise win before the fight, while the ignorant fight to win." - Morihei Ueshiba

Offline Ack-Ack

  • Radioactive Member
  • *******
  • Posts: 25260
      • FlameWarriors
Re: Which is best for a stable CH Setup....
« Reply #9 on: December 21, 2012, 07:34:22 PM »
The problem with CH gear is that they need 5volts through the USB port to work properly.  If the USB ports on your motherboard output a steady 5volts then there should be no issues connecting your CH USB gear directly through the USB ports on your motherboard.  If the USB ports on the motherboard aren't outputting the 5volts needed by the CH gear than it is recommended that you use a powered USB hub to ensure the CH gear gets the necessary power.

On my previous system, I had an ASRock motherboard that didn't output a steady 5 volts, so I had issue like spiking controllers around center and frequest loss of calibration or even Windows not seeing my controllers so I had to use a powered USB hub to get my controllers working properly.  When I got my new system, it has an ASUS motherboard with a steady 5volt output for the USB ports and I'm able to use the ports on my computer for my CH controllers without any problems as my CH gear gets the necessary power, unlike with my old ASRock motherboard.

ack-ack
Logged
"If Jesus came back as an airplane, he would be a P-38." - WW2 P-38 pilot
Elite Top Aces +1 Mexican Official Squadron Song

Offline Chalenge

  • Plutonium Member
  • *******
  • Posts: 15179
Re: Which is best for a stable CH Setup....
« Reply #10 on: December 21, 2012, 07:56:42 PM »
If you are using Windows 7 I suggest you use the powered hub either with or without the card.
Logged
If you like the Sick Puppy Custom Sound Pack the please consider contributing for future updates by sending a months dues to Hitech Creations for account "Chalenge." Every little bit helps.

Offline Changeup

  • Persona Non Grata
  • Platinum Member
  • ******
  • Posts: 5688
      • Das Muppets
Re: Which is best for a stable CH Setup....
« Reply #11 on: December 22, 2012, 01:17:35 AM »
Ok, it was miserable tonight.  I removed the POS powered USB hub and plugged straight into the MB on three ports.  I also removed the CH manager software.  The calibration numbers NEVER settled down all night.  I had to recalibrate twice and it never settled.  I calibrated in Windows first and that is a mess with CH gear.  The damn Microsoft stuff doesn't recognize each of the CH components for what they do because it wanted me to center my throttle?  Ok.

So then I installed the USB card and when it loaded the drivers the system ran beyond slow.  I had no idea a small board like that would dominate resources so THAT got jerked out too.  This sucks.  I've got plenty of power, 850W 80 Gold
« Last Edit: December 22, 2012, 01:19:08 AM by Changeup »
Logged
"Such is the nature of war.  By protecting others, you save yourself."

"Those who are skilled in combat do not become angered.  Those who are skilled at winning do not become afraid.  Thus, the wise win before the fight, while the ignorant fight to win." - Morihei Ueshiba

Offline Auger

  • Nickel Member
  • ***
  • Posts: 492
      • AKs Home Page
Re: Which is best for a stable CH Setup....
« Reply #12 on: December 22, 2012, 02:16:12 AM »
I have a Belkin 7 port powered hub with a full CH USB setup.  It has been rock solid for at least the past 4 years.  I use the CH Manager software with lots of buttons programmed.  Always solid performance.
Logged

Offline Chalenge

  • Plutonium Member
  • *******
  • Posts: 15179
Re: Which is best for a stable CH Setup....
« Reply #13 on: December 22, 2012, 03:39:22 AM »
Its not your gear. It is probably the settings you have under power management. I will have to look at it in more detail to sort it out. By the time I do someone else will probably have the solution posted.
Logged
If you like the Sick Puppy Custom Sound Pack the please consider contributing for future updates by sending a months dues to Hitech Creations for account "Chalenge." Every little bit helps.

Offline The Fugitive

  • Plutonium Member
  • *******
  • Posts: 17934
      • Fugi's Aces Help
Re: Which is best for a stable CH Setup....
« Reply #14 on: December 22, 2012, 09:39:33 AM »
Quote from: Changeup on December 22, 2012, 01:17:35 AM
Ok, it was miserable tonight.  I removed the POS powered USB hub and plugged straight into the MB on three ports.  I also removed the CH manager software.  The calibration numbers NEVER settled down all night.  I had to recalibrate twice and it never settled.  I calibrated in Windows first and that is a mess with CH gear.  The damn Microsoft stuff doesn't recognize each of the CH components for what they do because it wanted me to center my throttle?  Ok.

So then I installed the USB card and when it loaded the drivers the system ran beyond slow.  I had no idea a small board like that would dominate resources so THAT got jerked out too.  This sucks.  I've got plenty of power, 850W 80 Gold

Having all the power in the world isn't going to do you any good if it doesn't get through your MB to the CH gear you have plugged in. I have had the same Belkin 4 port ( they don't even offer it any more) for many years. I haven't calibrated my CH gear in years and haven't had any issues with spiking.

As AK-AK always says, YMMV
Logged
Pages: [1] 2   Go Up
« previous next »