Author Topic: PLeLv 44 Ju 88 (Read 1376 times)

Greebo · « **on:** March 04, 2005, 04:52:54 PM »

I've uploaded my Finnish Ju 88 to The Skin Department. Your insights would be much appreciated.

This skin has one or two issues which have caused problems on this scheme. First, the lower wing skins are mirrored, so the insignia on the right wing is back to front. Also the rear lower fuselage is triple patched, so I can't make the yellow stripe wrap fully around. There is a thin strip patch below the lower left tailplane which gets transferred above the tailplane. I had to leave this a compromise blue/green shade. Finally the spinners are mapped to a patch on the upper right wing. The tips should be yellow but this can't be done without leaving a yellow blob on the wing. So I made it grey and left a "paint chip" on the wing.

This is an aircraft of 3/PLeLv 44 flown by W/O Unto Oksala, Mannerheim Cross holder. Thanks Wmaker and Kantorri for all the info you got me on this aircraft and to Kwaessa, whose Finnish "dudes" I've used.

thebest1 · « **Reply #1 on:** March 04, 2005, 05:21:52 PM »

Awesome Greebo youve out dont yourself again.

Panzzer · « **Reply #2 on:** March 04, 2005, 05:30:17 PM »

That looks awesome, Greebo! Thank you.

edit: I'm visiting my parents so I don't have my books so I can't check what's wrong... But I don't think there's much that can be wrong, looks just beautiful.

SlapShot · « **Reply #3 on:** March 04, 2005, 05:33:02 PM »

I am assuming that you can't make the tips of the prop spinners yellow. Would some exhaust smudge around the cowlings be fitting ?

kanttori · « **Reply #4 on:** March 04, 2005, 06:11:37 PM »

THANK YOU GREEBO!

About 80 Finnish AH pilots are very grateful to you, we have wait this so long time!

Zuum · « **Reply #5 on:** March 05, 2005, 02:30:35 AM »

GREEBO!!!

Looks reeeeel goooood!

Wmaker · « **Reply #6 on:** March 05, 2005, 04:49:53 AM »

Thank you so much Greebo!!

A big, snappy

Vuokko · « **Reply #7 on:** March 05, 2005, 05:21:16 AM »

Thank you Greebo! Looks great, like all your skins.

rogerdee · « **Reply #8 on:** March 05, 2005, 08:14:15 AM »

very nice greebo makes my effort look like a kindergarten drawing,
keep up the good work

kanttori · « **Reply #9 on:** March 05, 2005, 08:45:27 AM »

I have checked all your panel lines, shutters (for ex. that one for the rubber boat) etc. and they're just correct! You have even the string to the rubber boat!

Have you send it to HTC yet? If not, please hurry up!;)

Greebo · « **Reply #10 on:** March 05, 2005, 01:44:39 PM »

Thanks for the kind words guys.

There is a fair bit of exhaust dirt on the cowling sides, it wasn't very visible in the first screenshots due to the angles they were taken at. I held back a bit on the weathering since in RL this plane had just been freshly repainted when it saw service.

I can make the spinner tips yellow but it leaves the yellow patch on the wing as shown below. Maybe it isn't too obtrusive though, what do you think?

I'll leave it until at least Monday before sending it in Kanttori, HTC aren't back until then anyway.

mechanic · « **Reply #11 on:** March 05, 2005, 01:56:35 PM »

I'd say keep the yellow, the spot on the wing isnt bad at all.

kinda nice to think the mechanics and painters might have spilt a drop

great work.

Paul · « **Reply #12 on:** March 05, 2005, 06:33:04 PM »

Nice work again Greebo... as usual.

SlapShot · « **Reply #13 on:** March 06, 2005, 09:24:18 AM »

Nice ... that little spot on the wing is minor in comparison to getting the spinners correct.

nopoop · « **Reply #14 on:** March 06, 2005, 12:56:37 PM »

Good stuff Greebo !!