Author Topic: Saitek 45 Problem (Read 350 times)

Harp00n · « **on:** January 02, 2008, 11:00:08 AM »

Hi,

played AH2 for almost a year now without any problems.

Today I installed the newest Saitek Drivers and all of a sudden I can´t calibrate the x & y axis correct in AH2. Windows calibration works fine with x & y axis, and shows full range of movement on the x and y axis.

In AH2 the dead center position is at "65535" and the full left position is at "0", pushing the stick to the right doesn´t show any result, x-Axis value stays at "65535". From a previous config-file I know that the dead center position should be at 35000 (something like that) and the full right position should be 65535.

Same with the y-Axis. It seems to work only half the way.

Wish I could remove this *§$!!-Saitek drivers but no way, and I don´t want to mess around with my registry, since calibration seem only to be a problem in AH2(?).

Any suggestions would be highly appreciated!

Already reinstalled AH2 without success though...problem still there.

zmeg · « **Reply #1 on:** January 02, 2008, 11:54:13 AM »

Go to your settings folder and edit the saitekx52flightcontrolsystem. cfg
file using notepad. the center number should be 32767.

Harp00n · « **Reply #2 on:** January 02, 2008, 12:26:43 PM »

Thx for your reply, but it doesn´t work. I altered that number like you suggested.

Now the elevator on the right wing is in a up-position, thats all.

Looks like AH2 thinks that the center-position of my stick equals a full right movement of the stick, so the range from 0 to 65000 is covered only by full movement to the left (value =0) to the dead center position (value=65000). Movement to the right is not recognized by AH2.

Same with y-Axis

Already tried to use standard windows drivers which where replaced by saitek-drivers but doesn´t work.

I´m confused!

Here´s the part of the config with the settings it produces after calibration:

Saitek X45 Flight Controller
6,34
X Axis
0,65535 (<---that should be around 34000) ,65535,0.053000,0.100000,0.250000
AXIS,ROLL,0,0
NOTUSED,NOTUSED,0,0
NOTUSED,NOTUSED,0,0
NOTUSED,NOTUSED,0,0
Y Axis
0,65535,65535,0.050000,0.100000,0.250000
AXIS,PITCH,0,0
NOTUSED,NOTUSED,0,0
NOTUSED,NOTUSED,0,0
NOTUSED,NOTUSED,0,0

Xasthur · « **Reply #3 on:** January 02, 2008, 12:42:59 PM »

System Restore and fk off the latest driver?

If it ain't broke, don't fix it?

Harp00n · « **Reply #4 on:** January 02, 2008, 03:31:06 PM »

Actually I tried to attach a X52 plus drivers to my system to replace my X45...but the 52´s stick seems to be dead. After I reaattached the 45-combo AH2 went crazy

Getback · « **Reply #5 on:** January 02, 2008, 04:19:47 PM »

Did you install the latest SST software? That caused me some issues.

Harp00n · « **Reply #6 on:** January 03, 2008, 05:58:38 AM »

Yes. Installed it and deinstalled it after it caused a bluescreen on startup.

Theres probably still some remains left that causes the problems I guess. Problem in AH2 disappeared yesterday, let´s see what happens after I restart my computer.

Getback · « **Reply #7 on:** January 03, 2008, 10:27:02 AM »

Restore. That ultimate best way to get things back to the good ole days.

I think the SST will probably work if you know how to set it up. I have never really needed it for anything or have taken the time to work with it.