« previous next »
Pages: 1 [2]   Go Down

Author Topic: Saitek X52 not working properly with AH  (Read 3664 times)

Offline Skuzzy

  • Support Member
  • Administrator
  • *****
  • Posts: 31462
      • HiTech Creations Home Page
Re: Saitek X52 not working properly with AH
« Reply #15 on: October 29, 2009, 12:52:59 PM »
Run DXDIAG and look under the "Input" tab.  Once you expand the USB devices section it should show the X52 and various bits of information about it.

If it shows there, is should just work in the game.  If it does not show there, then move to another USB port. 

By any chance did you disable the HID service?
Logged
Roy "Skuzzy" Neese
support@hitechcreations.com

Offline Raptor123

  • Zinc Member
  • *
  • Posts: 4
Re: Saitek X52 not working properly with AH
« Reply #16 on: October 30, 2009, 05:58:55 PM »
Sorry. I did not realize I was going off topic. I took it as the topic being issues with the saitek x52..I will not make the same mistake agaoin
Logged

Offline OOZ662

  • Platinum Member
  • ******
  • Posts: 7019
Re: Saitek X52 not working properly with AH
« Reply #17 on: October 30, 2009, 08:41:26 PM »
Quote from: Raptor123 on October 30, 2009, 05:58:55 PM
Sorry. I did not realize I was going off topic. I took it as the topic being issues with the saitek x52..I will not make the same mistake agaoin

You read that improperly. Niel probably started talking about something entirely different (like "just buy a CH stick" or something), so Skuzzy came a long, blanked his post, and replaced it with a note for him to see Rule #2 as to why his post was deleted. You're doing just fine. :)
Logged
A Rook who first flew 09/26/03 at the age of 13, has been a GL in 10+ Scenarios, and was two-time Points and First Annual 68KO Cup winner of the AH Extreme Air Racing League.

Offline Neil Roche

  • Zinc Member
  • *
  • Posts: 52
Re: Saitek X52 not working properly with AH
« Reply #18 on: October 30, 2009, 09:22:49 PM »
See Rule #4
« Last Edit: November 03, 2009, 05:58:38 AM by Skuzzy »
Logged
Herder

Offline Tilt

  • Platinum Member
  • ******
  • Posts: 7358
      • FullTilt
Re: Saitek X52 not working properly with AH
« Reply #19 on: November 01, 2009, 11:03:02 AM »
Raptor as Skuzzy says you should see the saitek stuff in Device manager > Human interface Devices


Quote from: OOZ662 on October 29, 2009, 08:02:30 AM

To find what Tilt is referring to (and honestly I don't know why he brought it up...none of that makes sense to me) go to Control Panel(classic view)>Game Controllers. A small window will pop up with the X52 listed. Press the Properties button.

Raptor the reason I leave this (Game controllers> Saitek x52 >Properties )running when playing AH is that its clear to me that AH see all the stick properties better when it is running in the back ground.

I leave all the Siatek controller ware switched off.

Every single button and switch gets a dx # within AH (that AH can recognise) which is not the case if Game controllers> Saitek x52 >Properties are switched off.
Logged
Ludere Vincere

Offline guncrasher

  • Plutonium Member
  • *******
  • Posts: 17362
Re: Saitek X52 not working properly with AH
« Reply #20 on: November 02, 2009, 07:56:09 PM »
I had lots of problems with the installed software that came with my x52.  I removed it and let windows decide which drivers were best.  havent had a problem since then and that was 3 months ago.

semp
Logged
you dont want me to ho, dont point your plane at me.

Offline Rich46yo

  • Platinum Member
  • ******
  • Posts: 7358
Re: Saitek X52 not working properly with AH
« Reply #21 on: November 03, 2009, 02:44:22 PM »
Are you running it thru a powered USB Hub?

A lot of my issues cleared up when I went into Saitek control panel and in the LEDs tab I turned the brightness all the way up. Apparently that is also a power setting cause my mouse jump issue went away completely. So did my axis jumping.
Logged
"flying the aircraft of the Red Star"
Pages: 1 [2]   Go Up
« previous next »