Author Topic: Win 2000 CD-RW Disaster (Read 570 times)

funkedup · « **on:** February 27, 2002, 05:12:20 PM »

DVD on Secondary IDE as Master. (Toshiba SD-M1502T)
CD-RW on Secondary IDE as Slave. (Acer 1610A)

Everything fine under Win 98SE.

I installed Win 2000 and there are constant errors. Buffer underruns, power calibration area full, etc.

Mobo is Epox EP8K7A (AMD 761)
Athlon 1333
512 MB RAM

Any ideas?

Related link:
http://www.computing.net/windows2000/wwwboard/forum/24768.html

minus · « **Reply #1 on:** February 27, 2002, 05:18:16 PM »

funked got similar problem but on diferent MB

it vas MSI bord and forget reinstal 4in1 ,becose i find NT run just fine without them but when tryed burn CD got damn problem after 20 % of burning runed always off from buffer

so try to install corect chipset drivers , maybe your W2K mising something for corect run

Animal · « **Reply #2 on:** February 27, 2002, 05:20:41 PM »

try to autoupdate windows
for windows xp there is an update for CD-RW errors.
maybe it was also posted for win2k

-ammo- · « **Reply #3 on:** February 27, 2002, 05:23:21 PM »

Have you installed win2K service pack 2?

Animal · « **Reply #4 on:** February 27, 2002, 05:26:52 PM »

Quote

Originally posted by -ammo-
Have you installed win2K service pack 2?

That goes without saying, but knowing funked, its possible he didnt

funkedup · « **Reply #5 on:** February 27, 2002, 05:31:29 PM »

I installed every darn thing on the Windows Update site. All my drivers are the latest and greatest too.

Problem also occurs if I swap the drives, i.e. CD-RW Secondary Master, DVD-ROM Secondary Slave.

I guess I'll try DVD-ROM as Primary Slave and CD-RW as Secondary Master next.

If not, back to Win98SE.

funkedup · « **Reply #6 on:** February 27, 2002, 05:40:45 PM »

Minus:

Here is the list of drivers from my MOBO:
http://www.epox.com/html/english/support/motherboard/drivers/download_ep-8k7a.htm

I didn't install the Miniport driver because there is no Win2k version.

I have the audio disabled so the VIA Apollo 686 chipset audio driver wouldn't install.

I did install VIA Apollo IDE busmaster.

I guess I should try uninstalling the busmaster driver, or finding a Win2k version of the Miniport driver?

bloom25 · « **Reply #7 on:** February 27, 2002, 05:43:55 PM »

Did you enable DMA mode for your cd drives? Under win2k it's under the properties for the "secondary channel."

mrsid2 · « **Reply #8 on:** February 27, 2002, 05:44:51 PM »

Funkedup although I use nearly similar setup and have no probs with my cd-rw, check http://www.viahardware.com where they have special versions of drivers for people who have cdrom related problems.

Check under the 4in1 download section.

Good luck.

funkedup · « **Reply #9 on:** February 27, 2002, 05:58:36 PM »

Yes DMA is enabled.

Why would I install VIA 4-in-1 drivers? It's an Epox mobo with AMD chipset.

mrsid2 · « **Reply #10 on:** February 27, 2002, 06:02:40 PM »

Ah so its a pure AMD machine?

Most AMD76x motherboards come with a combined VIA southbridge. That leads to the need of some VIA drivers + AMD AGP drivers instead of VIA ones.

I'm not familiar with your mobo so I can't say for sure.

Edit: I just checked, your mobo does have the 686B so you need to install VIA drivers for that. Those came with your original motherboard drivers naturally, but as you ran into problems you can try to install different versions from the viahardware site.

funkedup · « **Reply #11 on:** February 27, 2002, 06:13:07 PM »

OK that makes sense.

The IDE drivers I installed were from VIA, and they are the latest version. VIA site actually says CD-RW should run better without those installed, so I will try an uninstall.

mrsid2 · « **Reply #12 on:** February 27, 2002, 06:16:21 PM »

I did some browsing from viaarena.com:

Special Rom Drives (re-writers etc): Probably not recommended that you install the VIA IDE miniport Driver as the default Microsoft driver provides better support for such devices, in general. This is because ATA/ATAPI devices are controlled by complex commands and their drivers are written to comply with the Microsoft default IDE driver. But at the same time, in most instances the VIA IDE Filter driver would be beneficial for ROM drive stability.

There is a good comparison table of drivers at http://www.viaarena.com/?PageID=66

I initially bought a 761+686B motherboard but even after 3 weeks of continuous tweaking, I couldn't get it to run stable.

I changed it for this KT266A board which has been rock solid compared to the 686 board. My only problem is a randomly occuring BSOD which is a problem that will be addressed in W2k SP3 according to MS bulletins.

funkedup · « **Reply #13 on:** February 27, 2002, 06:59:39 PM »

Thanks all.
It's not solved but at least I have some things to try now.

funkedup · « **Reply #14 on:** February 27, 2002, 11:57:58 PM »

Uninstalled the VIA Bus Mastering drivers and I burned a CD-RW with no errors.

Time will tell if it is a true fix but it looks good.
Thx all!