Author Topic: CD-R Burning Error (Read 352 times)

Thorns · « **on:** October 12, 2003, 06:16:11 PM »

I get the below errors, and solutions when trying to burn a cd-r, and it might do it on the 4th, or 5th track written, then dumps the cd-r. Any suggestions what's happening, and what I need to do? It's a Plexwriter 16/10/40A with W2k. Thanks, Thorns

1.) E8004189f:Write error - recovery needed - [03/0C/07]
2.) E80041934: TrackWriter error - Flush Failed - [T7127]
TrackWriter error - flush failed
Problem:
An error occurred while trying to write to the CD-Recorder. After trying again to write to the CD-Recorder without success, Easy CD Creator sent a flush command to the CD-Recorder, but the flush command failed. Most likely this error message is accompanied by another error message that describes the cause of the original problem.
Solution:
·   Try another blank CD.

·   Try another brand of media.

·   Retry.

·   Reinstall Easy CD Creator.

3.)E80041925: TrackWriter error - Command retry failed - [T7118]
TrackWriter error - command retry failed
Problem:
The TrackWriter received an error while trying to write to the CD-Recorder, tried resending the command, and failed again. This error is usually accompanied by additional errors that describe the original error.
Solution:
·   Try another blank CD.

·   Try another brand of media.

·   Review the error message(s) that accompany this one.

·   Check for faulty or disconnected cables between your computer and your CD-Recorder.

·   Check for improper termination of the bus (SCSI only).

·   Restart your computer.

Pfunk · « **Reply #1 on:** October 13, 2003, 02:21:39 AM »

Solution #1 dump the bloatware Easy Cd-Creator and download Nero

http://www.nero.com/us/index.html

Twist · « **Reply #2 on:** October 13, 2003, 02:44:37 AM »

I'll second that, Nero has never let me down.

I have the TDK VeloCD writer and it works great.

I still use the TDK software to rip however.

Staga · « **Reply #3 on:** October 13, 2003, 06:12:37 AM »

Check if you have Ultra-DMA enabled.
control panel -> system -> device manager -> IDE ATA (or ATAPI) controllers -> primary (or secondary IDE-channel, depends in what IDE-cable your burner is connected) -> use DMA if possible

(Translated from Finnish Windows but I believe you'll get the point)

DAVENRINO · « **Reply #4 on:** October 13, 2003, 01:01:47 PM »

Quote

Originally posted by Pfunk
Solution #1 dump the bloatware Easy Cd-Creator and download Nero

Hmmm... I have been using Roxio for three years on one machine with a Plextor 16/10/40A under ME and later XP. Second box with XP and Plextor 40/12/40A using Roxio bout 18 months. Never made a coaster on either and I burn a lot of discs. I just use the cheap stacks of TDK media I get at Costco for .03 each.

Nero is a great program though. I have a copy of that and Plextools. I just got used to the Roxio interface and was too lazy to learn another since Roxio always worked fine for me.

DJ229-AIR MAFIA

Thorns · « **Reply #5 on:** October 13, 2003, 04:01:46 PM »

Thanks all for the replys,

But, it is still getting write error even in Feurio. Starts to write then on second or third write file getting error. I too have used Easy CD Creator for about 2 years now, then this. About a month ago I updated my OS to Win2k. It shows my hard drive, CD-RW burner, and CD-Rom all as SCSI, which they aren't. Can't get it to change to a driver without SCSI either. Give me back "Screendoor 98" Never had any problems with it...... Got any more suggestions? DMA is enabled also.

Thanks,
Thorns

DAVENRINO · « **Reply #6 on:** October 13, 2003, 07:16:22 PM »

I assusme you applied all the lastest Roxio updates applying to WIN 2000. Also, when I went to XP I had to toss version 4 and buy version5. I am not sure bout WIN 2000. I saw version 6 at Costco today.

DJ229 - AIR MAFIA