Aces High Bulletin Board

Help and Support Forums => All things VR => Topic started by: Pollock on December 21, 2025, 10:09:18 AM

Title: Entry into the VR world.
Post by: Pollock on December 21, 2025, 10:09:18 AM
Most of my squad runs VR, and they keep telling me even with all the hassles that they will never go back to a flat screen. My current set up is AMD ryzen 7 7800x3d, 32gig ddr 5 Ram, RTX 4060 ti 8GB graphics. I run an MSI 40 inch ultrawide monitor using track ir5.  I see the Meta quest3S is currently 250 bucks and the wife is asking what do I want for Christmas?  Is anyone using this headset or spec equivalent? I would plan on tethering via usbc to keep it charged and use my pc to drive the game.
Would I get good smooth gameplay? I only go below 60 in extreme furballs and massive ground attacks with my current display set at 3440 X 1440, which is plenty enough detail for me.
Title: Re: Entry into the VR world.
Post by: The Fugitive on December 21, 2025, 01:02:48 PM
Im pretty sure that if you down load the "meta" software for the headset it will check your computer to see if it is able to run the headset.

I have a Ryzen 5 7600, 32 gig of ram, RTX 4060 Ti 8 gig video card and run a Quest 2 with out issues. I dont think you'll have any trouble running it.

Aces High isnt hard on systems. The only issue you might have is the resolution may be lower than what your use to, however the immersion more than makes up for any lack.
Title: Re: Entry into the VR world.
Post by: Rocco on December 21, 2025, 01:27:05 PM
Your rig should run most headsets. You might have some trouble with high end ones like the Pimax crystal super, but shouldn't have any problems with any of the quests. I've never used a quest myself but I think you need a good cable to connect to your PC and keep it charged while running it.
Title: Re: Entry into the VR world.
Post by: hazmatt on December 21, 2025, 01:37:29 PM
Something to keep in mind when running VR is that it looks much better with higher super sampling. It makes things like cockpit gauges and planes at a distance much clearer. In my experience 1.5 SS is the point of diminishing returns. 1.3 is a good balance.

AH3 is very lightweight compared to most games for VR. I would bet you could run it with 1.3 SS with you're gear. The only real limitation that I see is the VRAM on the 4060ti. It could cause some mirco stutters in the game if you overload it. I don't see that happening in AH3.
Title: Re: Entry into the VR world.
Post by: JimmyD3 on December 21, 2025, 02:55:51 PM
I just got a new Quest 3, and am enjoying it very much. Still got a ways to go to get it all setup and working with me but, the immersion is amazing. I have found that in AH3, I still go to my monitor for any GV work and when flying bombers.

Hazmatt, not sure what  you are referring to with "super sampling", could you elaborate?
Title: Re: Entry into the VR world.
Post by: hazmatt on December 21, 2025, 03:06:07 PM
In the Oculus software, you select the settings for the headset. You can change the resolution there. You can actually set the resolution for higher then the VR headsets native settings. By doing this it makes the display much clearer on the headset. You move the slider from auto to manual. As you move the resolution higher, you will see 1.1, 1.2, 1.3 displayed as you increase the resolution. These numbers are the super sampling numbers. I don't recall the exact resolution for each but with each increase will increment up the super sampling number. Hope the helps.
Title: Re: Entry into the VR world.
Post by: Pollock on December 22, 2025, 09:43:22 AM
Thanks for all the feedback I really appreciate it!  I figure for 250 I can try it out and I it is not for me I can return them.  If I do like it and the video resolution is not that great I can upgrade to the next model up.
Title: Re: Entry into the VR world.
Post by: Eagler on December 22, 2025, 11:15:59 AM
My quest 2 is more than good enough to play AH with but my pimax Crystal Light is way better but it cost way more too..

VR is fantastic on either one in AH and haven't used my 32" monitor in AH since I  first got into it with the vive pro in 2018

You are in for a treat

Eagler
Title: Re: Entry into the VR world.
Post by: Pollock on December 26, 2025, 09:02:28 PM
I got the Quest 3s and a link cable, installed the meta sw and looking around the cockpit is a far as I can get it which is unbelievable!
The SW porks both my hotas and pedals, and only allows me to use the annoying controllers from the quest, which are horrible.  I would like to use my mouse, headset, and current hotas, what am I missing?
Title: Re: Entry into the VR world.
Post by: The Fugitive on December 26, 2025, 09:23:21 PM
I got the Quest 3s and a link cable, installed the meta sw and looking around the cockpit is a far as I can get it which is unbelievable!
The SW porks both my hotas and pedals, and only allows me to use the annoying controllers from the quest, which are horrible.  I would like to use my mouse, headset, and current hotas, what am I missing?

What is the SW in  "SW porks my..." Software? Maybe you need to unplug and replug the controllers to update the USB connections.

I have a Quest2 and have never used the VR controllers. All mappings need to either be re-done while in VR, or you can find the jsm files in the settings folder, copy them to your desktop, then rename them by adding "VR_" to the front of each file. Save the name change and move then back into the settings folder allowing them to over write the files that are there.

The mouse, the white ball is your cursor. I added two buttons to my stick, one a left mouse click, the other a right mouse click. Point the ball at what you want to activate and click the mapped button.
Title: Re: Entry into the VR world.
Post by: Pollock on December 26, 2025, 09:28:04 PM
Everything works fine outside of VR, how do you disable the controllers? I will try the file mod too thanks fugi!
Title: Re: Entry into the VR world.
Post by: Rocco on December 26, 2025, 11:58:49 PM
You might have to disable the virtual hands. In the clipboard go to options -> Preferences -> VR and check the disable vr hands. I also have auto swapping and virtual keyboard disabled.
Title: Re: Entry into the VR world.
Post by: Eagler on December 27, 2025, 07:33:45 AM
Yep as stated by Fugitive you need to setup your controllers separately for vr..

Make sure you have a center view button on your stick ..

Eagler
Title: Re: Entry into the VR world.
Post by: hazmatt on December 27, 2025, 03:02:36 PM
Everything works fine outside of VR, how do you disable the controllers? I will try the file mod too thanks fugi!

I just take the batteries out of my controllers since I don't use them.
Title: Re: Entry into the VR world.
Post by: Eagler on December 27, 2025, 05:47:19 PM
My quest 2 auto assigned the controllers instead of the hotas and I had to manually set them up on the laptop..

Eagler
Title: Re: Entry into the VR world.
Post by: JimmyD3 on December 27, 2025, 06:48:37 PM
My controllers are still in the box.
Title: Re: Entry into the VR world.
Post by: Pollock on December 27, 2025, 08:37:52 PM
2 days now and this set up makes me look like a friggin moron! My pc has plenty of juice to run this cartoon graphic game. I think it is the quest 3 link SW that is the issue.  It loses connection, when I look around the little hour glass spins. I started mapping from scratch and the settings do not hold.  Is there any other sw that will work with the tether? I have the correct cable. I am about ready to return this turd to best buy! I want something that connects through the displayport on graphics card.
My 4060 has plenty of power to run this game
Title: Re: Entry into the VR world.
Post by: hazmatt on December 27, 2025, 08:45:41 PM
2 days now and this set up makes me look like a friggin moron! My pc has plenty of juice to run this cartoon graphic game. I think it is the quest 3 link SW that is the issue.  It loses connection, when I look around the little hour glass spins. I started mapping from scratch and the settings do not hold.  Is there any other sw that will work with the tether? I have the correct cable. I am about ready to return this turd to best buy! I want something that connects through the displayport on graphics card.
My 4060 has plenty of power to run this game

What were the results of the USB cable link test?
Title: Re: Entry into the VR world.
Post by: Pollock on December 27, 2025, 08:56:43 PM
2.7GPS connection USB3
Title: Re: Entry into the VR world.
Post by: Vulcan on December 27, 2025, 10:03:02 PM
2.7GPS connection USB3

Check your audio settings, the quest 3 mic makes my AH lag out. So I use headphones connected to my pc for game audio and mic, not the quest ones.
Title: Re: Entry into the VR world.
Post by: Pollock on December 27, 2025, 10:05:04 PM
My controllers are still in the box.
You may have hit the nail on the head!  I removed the batteries and now I can make some progress.
Title: Re: Entry into the VR world.
Post by: Eagler on December 28, 2025, 06:23:58 AM
I went through a couple of usb-c cables for my quest2 because paying $80 to occulus for theorem cable seems like robbery...

But I haven't found a decent one that actually charges the headset enough while I play so I have to manually charge it every 4 days or so for my one hour of AH nightly...

If you want to upgrade you are probably over half way in $$$ to a Pimax Crystal Light...it connects to the graphics port , has much better resolution and sound when you graphics the DMAS earpiece upgrade..

Good luck with your vr as I think the experience is more than worth the hassle and expense..

Eagler
Title: Re: Entry into the VR world.
Post by: The Fugitive on December 28, 2025, 08:39:59 AM
Basics.....

When you log in the game in VR, after the login page, check the "video settings" to be sure your headset is on the right graphic card on your computer.

Next, not all headset cables are the same. Some are slow, some dont charge worth a crap, and others just fail now and then. I use...

https://www.amazon.com/dp/B081SHD773?ref=ppx_yo2ov_dt_b_fed_asin_title&th=1

With this USB-C powered hub

https://www.amazon.com/dp/B0C36LS9TC?ref=ppx_yo2ov_dt_b_fed_asin_title&th=1

USB-C ports are the fastest, and with the powered hub I get a good steady supply to the headset.

If you are not using a USB-C port, be sure you are using the 10Gbps USB ports, they are "teal blue" not the regular blue of most USB ports. The regular ports are only 5Gbps speed and so will give you trouble with  not enough band width. If using the USB port this cable is an option.

https://www.amazon.com/Premium-Cable-Charging-Compatible-Quest-Oculus/dp/B0DR8WSGYH/ref=sr_1_2?crid=2SDX5YF3UL7ZL&dib=eyJ2IjoiMSJ9.vWRBSApZjeuTwape7qEMSvlvC07fpd_3FqV3HqntM7czykCfCXQfHzmWuYXf6Id8s-L-baq6t_HnyvklUXKde4Y9qIjZX5KY6CPaFVj5cconEH2w59FqPpVp_SPuD4ERuRo_917a6wSAKKxIEekUARtRhozCPEk_iRYFC0hA4fB43tzdWCV_-OPd6C7-V4RmelAk5PilSJec8llfwd-7GLH3BMAugJnANmCtKXuPd5rQdQAnORgHn0X0U3-C7LSlX6RSkS5dm9LXCtrlz4Y1NbQ96UgtcdhMweDlj8fw8b8.YCW3gM1wNMyYsT9IKYCTfZ3qJn_Ka3JAaMQgfCbRYJc&dib_tag=se&keywords=INIU+DI401+16FT+VR+High+Speed+Transfer+Link+Cable&nsdOptOutParam=true&qid=1766931968&s=electronics&sprefix=iniu+di401+16ft+vr+high+speed+transfer+link+cable%2Celectronics%2C176&sr=1-2

I havent used this one but I have seen a number of "comparison" videos and this one always rates high. It connects through the USB 10Gbps port and to the headset, but has the charging block in-line. Add a USB-C cable to a fast charging plug and it should keep the headset charged while you play, even for long sessions.

I dont have any trouble with the headset speakers, but the mic was always too low. I added a lapel mic...

https://www.amazon.com/dp/B077VNGVL2?ref=ppx_yo2ov_dt_b_fed_asin_title

And attached it to the side strap and it works great.
Title: Re: Entry into the VR world.
Post by: Pollock on December 28, 2025, 11:17:08 AM
Thank you all for the help, I am finally flying! Main issue was the hand controllers, once batteries were removed I was able to navigate in the VR world!
So far my direct connect via USBC seems very stable, I ordered one of the cables that charges and moves data at the same time.  The micro freezes when keying mic seem to also be resolved by using my PC headset.  Now I need to get over the motion sickness, I hear that is normal for the first week.
Title: Re: Entry into the VR world.
Post by: Eagler on December 28, 2025, 11:34:46 AM
A small desk fan blowing in your face might help get over the motion sickness..

Another way is to play Jet Island on steam as it's vr motion sensation is 100x stronger in that game on its hover board than AH vr is at its worse..

Eagler
Title: Re: Entry into the VR world.
Post by: Vulcan on December 28, 2025, 05:45:17 PM
For my Quest 3 I use this USB cable: https://www.amazon.com.au/dp/B0F1CMG4BF?th=1

And this charger: https://www.amazon.com/UGREEN-Charger-iPhone-Galaxy-MacBook/dp/B0DMFFK5LV

My Quest 3 is plugged directly into the USB 3 port on my PC, and this charger sits inline so the battery never drops any charge when I'm playing on my PC.

Title: Re: Entry into the VR world.
Post by: Vulcan on December 28, 2025, 05:47:51 PM
The micro freezes when keying mic seem to also be resolved by using my PC headset.

I've ended up using a USB mic on my desk as I got sick of my headset falling off when I'm looking up. So I end up using my Quest audio for sound output and the USB mic for vox.