« previous next »
Pages: [1]   Go Down

Author Topic: Y axis is freaking out on my X45  (Read 278 times)

Offline bizket

  • Copper Member
  • **
  • Posts: 323
Y axis is freaking out on my X45
« on: November 26, 2002, 12:48:22 AM »
I'm havinng problems with the y axis just going dead and losing all elevator control. It seems to be pretty random, I'll be flying along just fine than it just dies with no warning. I cant calibrate in windows or in Aces High, but if I leave the stick alone for a few minutes and come back it calibrates fine. Have my pots gone bad?? Does thing thing even have pots???? I've only had the stick for a couple of months so I dont know a whole lot about it.

System
Win 98SE
AMD Athlon Tbird 950
Asus A7V KT133A Motherboard
384 MB RAM
Direct X 8.1

BTW this happpens in Aces High and in a couple of other games I've been playing. The only change I've made to my system is DirectX 8.1 but it worked fine for a week or two after I installed it.
Logged

Offline Xjazz

  • Gold Member
  • *****
  • Posts: 2653
Y axis is freaking out on my X45
« Reply #1 on: November 26, 2002, 01:47:48 AM »
S!

If find this information from Migmans sim site long time a go. I dont know if  Saitek X45 different pots that X36.

Saitek Repair Shop - X36 Pot specs      

Total Resistance:       500 Ohm-1M    
Tolerance:          + _ 20 %    
Linearity:          B B Curve 0.5W    

Rated Power:          0.25W Other than B curve    
Max rating:          500VAC 250 VDC    
Noise:             47 mv    

Insulation Resistance Rating:    100 M Ohm at 500 VDC or VAC for one minute    
Total Turning Angle:       300 deg. +- 10 deg    
Stopper Strength:      5.0 Kg/cm max    

Turning Force:          10 - 30 gf/cm    
Axis push/pull force:       10.0 kg/cm    

Residual resistance between Terminals 1 and 2: 10 Ohm Max    
Residual resistance between Terminals 2 and 3: 10 Ohm Max
Logged

Offline OZkansas

  • Nickel Member
  • ***
  • Posts: 647
Y axis is freaking out on my X45
« Reply #2 on: November 26, 2002, 08:59:45 AM »
Have you opened it up to see if the pots are secure?  I suspect that the hot glue that holds the pots in place has failed:(  Possible connection to pots has failed.  Should be a problem that is visible with the old naked eye.  Good luck.
Logged

Offline Eagler

  • Plutonium Member
  • *******
  • Posts: 18219
Y axis is freaking out on my X45
« Reply #3 on: November 26, 2002, 09:45:43 AM »
sounds like time to whip out the in store replacement policy
Logged
"Masters of the Air" Scenario - JG27


Intel Core i7-13700KF | GIGABYTE Z790 AORUS Elite AX | 64GB G.Skill DDR5 | 16GB GIGABYTE RTX 4070 Ti Super | 850 watt ps | pimax Crystal Light | Warthog stick | TM1600 throttle | VKB Mk.V Rudder

Offline bizket

  • Copper Member
  • **
  • Posts: 323
Y axis is freaking out on my X45
« Reply #4 on: November 26, 2002, 10:30:22 AM »
Yeah thank God I spent the 10 bucks on that.
Logged

Offline Eagler

  • Plutonium Member
  • *******
  • Posts: 18219
Y axis is freaking out on my X45
« Reply #5 on: November 26, 2002, 11:13:39 AM »
Quote
Originally posted by bizket
Yeah thank God I spent the 10 bucks on that.


as I've posted before, CompUSA gave me another $10 replacement policy on the replacement! Be sure to check out that possibility too ..
Logged
"Masters of the Air" Scenario - JG27


Intel Core i7-13700KF | GIGABYTE Z790 AORUS Elite AX | 64GB G.Skill DDR5 | 16GB GIGABYTE RTX 4070 Ti Super | 850 watt ps | pimax Crystal Light | Warthog stick | TM1600 throttle | VKB Mk.V Rudder

Offline bizket

  • Copper Member
  • **
  • Posts: 323
Y axis is freaking out on my X45
« Reply #6 on: November 27, 2002, 12:45:44 AM »
Well, I hooked my MS Precision Pro back up tonight. The X45 is going back to Best Buy on Friday, I think its toast:(
Logged
Pages: [1]   Go Up
« previous next »