Author Topic: Back left up view in P51d (Read 751 times)

Stegahorse · « **on:** August 31, 2005, 02:17:21 AM »

Tried to adjust the back-left up view (1+5 key combo) and press f10 to set in the 51D. No message that the setting has been set nor does the view hold to what I want it to be. Please fix?

OOZ662 · « **Reply #1 on:** August 31, 2005, 04:58:23 AM »

If more than three buttons are pressed at once, the motherboard speaker will beep and the presses won't register.

Stegahorse · « **Reply #2 on:** August 31, 2005, 04:26:04 PM »

this is just 2 buttons and view won't hold once set

Schutt · « **Reply #3 on:** September 01, 2005, 02:40:17 AM »

Works for me, i tried it.

Maybe you have a write protection on the file that saves the views, hard drive next to full or anti virus program messing up?

Stegahorse · « **Reply #4 on:** October 15, 2005, 06:54:08 PM »

It seems that the back up left is still non functional. It is in all planes. I press 5 and 3 together on number pad and shift the veiw to what I want then hit F10 to save. No message saying the setting has been saved like appears with all the other views. I did a full install of game after patch 3 and the problem persists, even after the full install.

WMLute · « **Reply #5 on:** October 16, 2005, 11:22:06 AM »

use your joystick hat for back view, keypad 5 for up, and then hit F10.

Can't hit three buttons at the same time. (i.e. kp 3 kp 5 and f10=3)

GunnerCAF · « **Reply #6 on:** October 16, 2005, 01:58:51 PM »

If he can press two keys (KP5 and KP3) then adjust the view (cursor or pageup pagedn) He is pressing 3 keys. I wouldn't think this is a problem pressing 3 keys at one time. I can press 3 keys at one time, not 4.

Gunner

Stegahorse · « **Reply #7 on:** October 16, 2005, 04:15:24 PM »

Its actually 5 and 1 for back up left. 2 keys. I can adjust the view in all other views BUT that one. It won't hold. Does not matter if I'm using hat keys or keyboard THAT one won't hold the setting. I can use arrow or page up/page down to move it around but F10 does not work ON THAT ONE. No mesage appears saying the head position had been saved ON THAT ONE view. Head position works on all other views BUT THAT ONE.

GunnerCAF · « **Reply #8 on:** October 16, 2005, 08:44:38 PM »

Stegahorse,

I just tried adjusting that view and saving the view. It worked on my PC. One thing you could try is to eliminate the possibility of hardware problems. If you have some way to test your keys to make sure you don't have a bad one. Most likely your KP1, KP5 or even the F10.

Good luck!

Gunner

Stegahorse · « **Reply #9 on:** October 17, 2005, 08:40:20 PM »

it ain't the keys, I can change the viewing angle, I just can't get the head position to hold where I want. F10 does not work on THAT ONE VIEW.
How many times I got to repeat it?
It must be a programming glitch.
It has been around for a while, like since 2.01.
I had hoped that it would be fixed by now.

Krusty · « **Reply #10 on:** October 17, 2005, 10:05:18 PM »

Works for me

Cobra412 · « **Reply #11 on:** October 17, 2005, 11:27:19 PM »

I only fly the mustangs and I've never ran into this issue either. All hat views work perfectly fine for me.

Stegahorse · « **Reply #12 on:** October 18, 2005, 09:04:02 PM »

Then i appears that I need to redo all the .cfg files. 1 works ok and 5 works ok.
1+5 does not.
What I need is not derision, but advice on how to fix it.

OOZ662 · « **Reply #13 on:** October 18, 2005, 09:49:12 PM »

Seeing as you're about the only one in history to have this problem, I'm not sure anyone will have an answer.

Schatzi · « **Reply #14 on:** October 19, 2005, 03:51:48 AM »

One thing you could try is: Dig up the config file for the D-Pony in your settings folder and delete it (make a copy of it somewhere else as a backup). Try from scratch one so to speak. Maybe that helps... or email skuzzy at HTC, although im not sure hes got the time to reply at the moment.