Author Topic: Help with CH Pro Throttle Settings  (Read 1113 times)

Offline LBurke6652

  • Zinc Member
  • *
  • Posts: 21
Help with CH Pro Throttle Settings
« on: December 31, 2008, 11:13:05 AM »

Operating my CH Pro Throttle, it seems that there are only two settings: full throttle (pushed forward) and zero (or minimum) throttle (pulled back) with no gradual increase/decrease as I push forward/pull back.  In other words, all or nothing with no in-between.  My Saitek X52 throttle allowed me to increase/decrease throttle gradually as much as I needed to.  Its gotta be me!  I have to be doing something wrong--or not doing something I need to do--to make the throttle work the way it should. 

Referring to the AH2 game controller mapping, under the heading "Controller Input", I have "Z Axis (65535)" and the corresponding "Mode 1 Function" of "Analog Inputs Throttle 1."  For "Y Axis (0)" I have no entry under "Mode 1 Function".  The same is true of "X Axis (65535)".  1.) Do I have the correct Mode 1 Function for the Z Axis?  If not, what needs to be there?  2.) Do I need to have an entry under "Mode 1 Function" for either or both the Y Axis and the X Axis?  If so, what is the correct entry for each?

Any help would be much appreciated.

Offline Hajo

  • Platinum Member
  • ******
  • Posts: 6034
Re: Help with CH Pro Throttle Settings
« Reply #1 on: December 31, 2008, 11:57:53 AM »
Select CH Throttle as Throttle 1.  That should clear your problem.  Don't forget Z as the axis. Or SLider.
- The Flying Circus -

Offline LBurke6652

  • Zinc Member
  • *
  • Posts: 21
Re: Help with CH Pro Throttle Settings
« Reply #2 on: December 31, 2008, 02:19:18 PM »

Thanks for the reply, Hajo. :salute

Your mention of "slider" caused me to remember to check Control Panel/Printers and Other Hardware/Game Controllers.  I saw that I could calibrate the throttle there and didn't recall ever doing that.  Sure enough, I calibrated it there and now it works like a charm.

Now that I have that problem taken care of, is there any point in me using two of my controller buttons for RPM up/down as I have been or would they be better used for something else on the theory--which could be wrong-- that now my throttle serves essentially the same function as RPM up/down?

Offline lowZX14

  • Silver Member
  • ****
  • Posts: 1340
      • Home of the 325th Checkertails VFG
Re: Help with CH Pro Throttle Settings
« Reply #3 on: December 31, 2008, 02:22:16 PM »
You're throttle shouldn't be adjusting your RPM but rather your manifold pressure, you can always use something else for RPM which I rarely use except for formation flying or trying to conserve fuel at cruise speed.
« Last Edit: December 31, 2008, 02:28:46 PM by lowZX14 »
lowZX14
325th Checkertails VFG
www.325thcheckertailsvfg.com

Offline wrag

  • Gold Member
  • *****
  • Posts: 3499
Re: Help with CH Pro Throttle Settings
« Reply #4 on: December 31, 2008, 02:24:02 PM »
I recommend that the CM program from CH be used for calibrating in windows!

I had trouble with my throttle until I installed and used it.
It's been said we have three brains, one cobbled on top of the next. The stem is first, the reptilian brain; then the mammalian cerebellum; finally the over developed cerebral cortex.  They don't work together in awfully good harmony - hence ax murders, mobs, and socialism.

Offline Getback

  • Platinum Member
  • ******
  • Posts: 6364
Re: Help with CH Pro Throttle Settings
« Reply #5 on: December 31, 2008, 06:32:32 PM »
I recommend that the CM program from CH be used for calibrating in windows!

I had trouble with my throttle until I installed and used it.

I read on CH's site or a related site that the CM actually contains drivers for the controls.

  Created by MyFitnessPal.com - Free Calorie Counter

Offline Hajo

  • Platinum Member
  • ******
  • Posts: 6034
Re: Help with CH Pro Throttle Settings
« Reply #6 on: January 01, 2009, 09:17:59 AM »
Getback yes.....on the disk that you get when purchasing CH products you get the latest drivers and the latest version of Control Manager.
- The Flying Circus -