AH Fantasy Plane Mod Thread

[Wildcatdad]

B-29 with forward firing 37mm guns from the P-39( I would say 2-3 between each engine), empty the bomb bay and fill it with downward firing 75mm guns from the B-25( maybe 4 or 5?) and make every gun position have quad 20's, like in the tail of the lanc! 

[Wiley]

They could fit a couple of 20mm cannons on wing mounts.

(Image removed from quote.)

ack-ack

If the ammo amount were decent you'd need a stick of dynamite to get me out of it.

Wiley.

[ReVo]

Fw-190D9 with the following modifications

Removal of the 13mm MG's, all radio equipment, and the aft fuel tank.
Modify flaps for high speed deployment, modify wings with leading edge slats.
Installation of the Jumo 213F. (Same engine used in the Ta-152 minus the intercooler)
Installation of a single MG151/20 in the nose.

[skorpx1]

My list of mods.


FM2 with 2x 20mm Hispanos.

P38J with 2x 20mm Hispanos in the nose, and 2 .50 cals next to the cockpit on both sides.

P47M with 6 20mm Hispanos and 2 .50 cals in the nose.

Ki-84 with 4 cannons instead of 2 .50's and 2 20mm's.

A6M (32) with more armor and a better engine.

190A8 with 4x 30mm's in the wings and 2x 20mm's in the nose.

Typhoon with an even bigger engine and two .50's in the nose, along with the 20mm's replaced by 30mm's.

P51D with more rigid wing structure, bigger engine and more aerodynamic frame and the ability to carry 4x 1000 pound bombs, 10 rockets and a center racked 500 pound bomb, or 2x 1000 pound bombs, 16 rockets and a center racked 500 pound bomb. Basically a flying ball of destruction.

[Karnak]

I wonder.. I'd gut the 30mm out of the 410s, the 13mm from the G6s, and the G2s engine.

Mod the E4 with 2x13mm in the nose and a 30mm in the Hub.
Retractable tail wheel.
Remove the MGFFs and smooth out the bumps, increasing roll rate.
Replace the canopy with curved plexi to have it Yak3 style but retaining the razorback, adding mirrors to the canopy ring.
Replace the spring loaded slats with 262 style ball bearing slats (which are not on the AH 262 )
Replace the 3 blade for a Spit14 style 5 blade prop

Worried about weight I'd adjust the ammo loads 500x13mm and 40x30mm, lower the power output to match a 3bladed; improving fuel efficiency so I could carry less fuel.
Keep it no more than 6400lb at full fuel.

That is pretty extreme, but the 30mm MK103 is a no go in your setup.  It won't fit.  Physically impossible.

[LCADolby]

That is pretty extreme, but the 30mm MK103 is a no go in your setup.  It won't fit.  Physically impossible.

prove it

[pipz]

I would take the inline engine out of the KI61 and put a radial in it! 

[ReVo]

I would take the inline engine out of the KI61 and put a radial in it! 

That sounds quite reasonable! Perhaps we could call it the Ki-100? 

[Karnak]

prove it

Such proofs are already out there.

[FTJR]

I'd do this to the P-38.

ack-ack

Why didn't they produce it Ack?

[mbailey]

KI-61 ....with the 109K4   DB 605DB or DC engine with MW 50 Methanol Water injection equipment and 4 hispanos in the wings with slightly larger flaps....  (your welcome Tongs   )



P38..... Nothing...shes perfect just as she is   

[Debrody]

190D, 4 blade prop added, wing 20mms and cowl guns removed, the 152's tater added to the prop hub, flaps enlarged, 109 style leading edge slats added.

[LCADolby]

Such proofs are already out there.

So even heavily modified to fit, it wont fit... be right back...



MORIARTY!!!!!!!!!!!! 

[Dragon]

KI-61 ....with the 109K4   DB 605DB or DC engine with MW 50 Methanol Water injection equipment and 4 hispanos in the wings with slightly larger flaps....  (your welcome Tongs   )

 

[ReVo]

So even heavily modified to fit, it wont fit... be right back...



MORIARTY!!!!!!!!!!!!  

Just duct tape it to the engine cowling.